크로매틱 예열 ... 가장 근접한 달걀 부화기 / 퍼 옴

급하게 아이스박스와 전구,공기순환팬으로만 만든 간이부화기가 외부온도에 영향을 많이 받아 34도에서 40도까지 수시로 변하는 등 불안정했습니다. 알속에 아리가 죽을까봐 부화기를 가까이 두고 수시로 확인하며 지냈지만 날짜가 지날수록 불안한 마음이 커져 온도 조절기를 추가 했습니다. 인터넷에서 3200원에 판매되는 온도조절장치 입니다. 요거 크기는 작지만 디지털방식이며 작동도 완벽하더군요 부화하기 전에 암탉이 포란하면 좋으련만 혹시 육추기가 필요할수도 있어 2개를 구입했습니다. 아래 단자 4개중 오른쪽 2개는 조절기전원으로 직류 12볼트, 왼쪽 2개는 스위치회로.. 중간 까만보턴 3개는 왼쪽부터 온도 및 모드셋팅,  +,  -  입니다. 온도스위치는 상한(히팅),하한(쿨링) 선택이 가능하며 부화기용이니 히팅으로 놓고, 온도 38도, 간격을 0.1도로 셋팅하니 내부 온도가 37.7~37.9도 사이를 유지하네요 자작부화기 만드시는 분들 요거 추천합니다. 아이스박스도 조금 큰것으로 바꿨습니다. 새로 만든 간이 부화기입니다(자동 전란장치만 추가하면 쓸만 하겠어요) 제품구입 문의가 있어 내용추가합니다. 위의 제품은 옥션에서 w1209로 검색하시면 여러 가격대가 나오는데 기능은 동일한듯 하구요. 셋팅 파라미터나 단자 세부사항은 여기저기 제품 상세설명 보면 알 수 있습니다. ------------------------------------------------ 온도 유지는 아주 정밀할 것 같다.... 이 제품은 12v 를 동력으로 쓰는데 , 히팅필름은 5v 이니 ... 이 패널이 5v 에서도 정상작동한다면 당장 해결이 될텐데 .... 반대로 12볼트를 쓰는 히팅필름을 구하면 해결될 것 같은데.... -------------------------------------------------- 비슷한 다른 온도조절기 이 놈에 대한 설명서 ...  빌어먹을 영어다.. Features 1, the chip technology for higher performance, lower power consumption! 2, the positive and negative elements are designed for embedded panel installation 3, high-speed flash RAM chip 4, setting off automatic memory 5, the control accuracy of 0.1 degrees Celsius 6, the key buzzer (to close) 7, high temperature alarm buzzer (0-110 degrees of freedom set) 8, hysteresis setting 0.5 onwards, you can control the number of decimal (0.5 to 15.0)   Second, the technical parameters Temperature control range: -50 ~ 110 C Resolution: -9.9 to 99.9 0.1 C when other temperature ranges 1 C Temperature measurement accuracy: 0.1 C Control accuracy: 0.1 C Backlash accuracy: 0.1 C Refresh rate: 0.5 S Input Power: DC / AC 12V Measuring input: NTC (10K 0.5%) Waterproof sensor Output: 1 relay output, capacity = 10A Environmental requirements: -10 ~ 60 C Humidity 20% -85% Size: 78 * 51mm (M3 mounting holes diagonal 75mm.) Power consumption: Quiescent Current: ≤35MA pull current: ≤65MA   V. Parameter Function Press SET 5 seconds to enter the main menu settings, press the + - automatically switch P0 ... P8 long press SET to confirm or 10 seconds without button operation controller returns P0 cooling, heating mode Press SET 5 seconds display P0, press SET to set to work mode, press + - to switch the heating mode [H] [C] for the cooling mode press SET to return, long press SET or automatically confirmed 10 seconds no key action controller carry out Cooling mode when the temperature measured value ≥ set point temperature, the cooling relay, refrigeration is started; when the temperature measured value ≤ temperature set point - hysteresis, the cooling relay switches off, cooler close Heating mode when the temperature measured value ≤ temperature set point, the heating relay, the heater starts; when the temperature measured value ≥ set point + hysteresis temperature, heating the relay off, the heater is off P1 hysteresis setting Press SET 5 seconds display P0, press + - Switch to P1, press SET to set back the difference, press + - to set hysteresis 0.5 to 15, according to a SET return is completed, long press SET, or 10 seconds without button motion controller automatically confirm completion Cooling mode when the temperature measurement value ≥ set value, the relay, the refrigeration starts; when the temperature measured value ≤ set value - the difference back when the relay is switched off, the cooling off. Such as the environment setting value is 30 C 25 C, hysteresis is set to 2 C, after power relay closed refrigeration starts, when the cooling to 23 C, the relay off cooling off, this time due to cooler has been broken open the temperature began to rise, rise to the set value when 25  C, the relay is closed cooling starts again, so repeated cycle control temperature not higher than 25 C Heating mode when the temperature measurement value ≤ set value, the relay, the heater starts; when the temperature measured value ≥ set value + return difference, the relay off, the heater is turned off. Such as the environment setting value is 10 C 25 C, hysteresis is set to 2 C, after power relay closed heater starts, when heated to 27 C, the relay off the heater turned off, this time because the heater has been broken open temperature begins to drop, the moment when the set value falls 25 C , the relay is closed heater starts again, so repeated cycle control temperature not lower than 25 C P2 highest temperature setting limit To avoid misuse others leads to a set temperature too high risk that the thermostat has the highest cap function limits the maximum temperature set point control thermostat setting range Press SET 5 seconds display P0, press + - to switch to the P2, press SET to set maximum limit, Press + - to set up the set temperature, the maximum is 110, according to a SET return is completed, long press SET or 10 seconds of no button action controller automatically confirm completion For example A setting of 60 highest temperature set point can only be set to 60 C temperature set point if you want to expand the scope of higher temperatures, you need to adjust the upper limit of setpoint. P3 set minimum temperature limit To avoid misuse others leads to the occurrence of ice blocking temperature is too low, there is the lowest of the thermostat set lower limit function, defining a minimum temperature set point control thermostat setting range Press SET 5 seconds display P0, press + - Switch to P3, press SET to set the minimum limit, Press + - to set the lowest temperature setting, the lowest value of -50, press SET to return after the completion of a long press SET or 10 seconds of no button action controller automatically confirm completion For example A setting of 2 the minimum temperature set point can only be set to 2 C temperature set point if you want to expand the scope of a lower temperature, we need to adjust the setting value lower limit. P4 temperature correction When measuring the temperature and the standard deviation of temperature or because the user hardware has special needs, you can use this function to correct temperature corrected = temperature correction + correction before the effective range of -7.0 to 7.0 Press SET 5 seconds display P0, press + - Switch to P4, press once SET correction, press + - to set the correction value, press SET to return after the completion of a long press SET, or 10 seconds without button operation controller automatically confirm completion For example, the normal display is 25 degrees; temperature correction is 0:00 Show 25 degrees; temperature corrected to show 26.5 1.5 degrees; temperature correction to display 23.5 -1.5; P5 delay start time units: minutes When the cooler or heater work delay necessary, on delay function, protective equipment life Press SET 5 seconds display P0, press + - Switch to P5, press SET to set delayed start time is in minutes, press + - to set 0-10 minutes, press SET to return after completion, or 10 seconds long press SET No keystrokes controller automatically confirm completion Cooling mode the first power after if the current temperature ≥ set value, the cooler will not start cooling, run the set delay time starts immediately Heating mode the first powered, if the current temperature ≤ set value, the heater will not immediately start the heating, you need to run the set delay time start Downtime refrigeration or heater between adjacent two starts when the delayed start time is greater than the set value, the cooler immediately start; Shutdown cooling or heater adjacent lapse between two starts is less than the delay start time setting, start again after the need to run chillers complete set delayed start time, the device to start. Delay time is counted down moments. For example, the cooling status is set to 5 minutes delay, the start delay after power refrigerator, five minutes after opening the refrigerator when it reaches the desired temperature of the refrigerant is stopped, then the start time, the next time the refrigerator immediately start counting completed work, not to wait for the completion of counting the timing end to work, delay in the LED blinks Delayed start setting of 0 equals off delay functions P6 key tone switch Press SET 5 seconds display P0, press + - Switch to P6, press the SET button sound set is turned on, press + - to set the on / off, press SET to return after the completion of a long press SET, or 10 seconds without button operation control Automatic confirmation completion Buzzer switch points on / off button is set on the key issue with the sound drops when action closes the buzzer is set to off, no sound button P7 temperature alarm Press SET 5 seconds display P0, press + - Switch to P7, press once SET display on / off (set to shut off the secondary function) is set to on and press the SET temperature can be set to a high temperature alarm point, press + - to set 0 to 110, after the completion of press SET to return, long press SET, or 10 seconds without button operation controller automatically confirm completion High temperature alarm setting range is 0-110 times or shut off function, shortness of arrival buzzer beeps after high temperature alarm, while forcibly disconnect relay For example, we give a liquid or a space heated to 40 degrees, set the temperature 80 degrees is dangerous, irresistible work process due to external factors cause the temperature higher than 80 degrees dangerous temperature, high temperature alarm relay off buzzer starts shortness alarm, timely alert staff to take appropriate measures to recoup their losses! Alarm temperature can be set according to actual needs, if you do not want this function to the temperature set to off, note that when the temperature returns to normal automatic discharge temperature alarm thermostat work properly P8 restore factory settings Some man-made causes internal thermostat settings chaos, one by one to set the time-consuming, then use this function to restore the factory settings, specific methods Press SET 5 seconds display P0, press + - Switch to P8, press SET to on or off, on to restore the factory settings, off to not perform any action, press SET to return after completion, or 10 seconds long press SET Bell is no key action controller automatically restore factory settings parameters as follows